I'm planning to use my TonidoPlug2 (TP2) for reading out the electricity production of my solar panels. I attached a very small USB bluetooth dongle to my TP2. The USB bluetooth device is detected, but the default kernel has no bluetooth support:
root@TonidoPlug2:~# lsusb ... Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) ...
The only solution to this problem is to build a new TP2 kernel with bluetooth enabled. The next section details the specific steps that did the trick for me.
Important note: Do NOT change the kernel on the internal flash memory as it might brick your device! Configure your TP2 to boot from the SATA HD first. I created a dedicated 32GB boot partition on my SATA device. Details:
- best manual: http://www.tonido.com/communitywiki/doku.php?id=advanceduses:usbboot (pay special attention to the fdisk part as the TP2 can only boot from "msdos" partitions)
- other info: http://www.tonido.com/support/display/docs/Booting+off+USB+Drive
Once you are booting from the SATA HD, you can proceed with the instructions below.
Building a TP2 kernel with bluetooth
The arm-kernel can be built on a linux desktop. I used my regular Ubuntu laptop.
First start with building a normal TP2 kernel:
- note that the url to download the kernel changed: http://www.tonidoplug.com/partners/topkick/2011/kernel/source/kernel-2.6.31-topkick1281p2-codelathe-20111122.tar.bz2
After you built the kernel and modules you can enable bluetooth by modifying the .config file:
- Options to enable: (toggle by pressing 'space' until an * or M appears)
- Networking → <*>Bluetooth subsystem support (CONFIG_BT)
- Networking → Bluetooth subsystem support → <*>L2CAP protocol support (CONFIG_BT_L2CAP)
- Networking → Bluetooth subsystem support → <*>SCO links support (CONFIG_BT_SCO)
- Networking → Bluetooth subsystem support → <*>RFCOMM protocol support (CONFIG_BT_RFCOMM)
- Networking → Bluetooth subsystem support → [*]RFCOMM TTY support (CONFIG_BT_RFCOMM_TTY)
- Networking → Bluetooth subsystem support → <*>BNEP protocol support (CONFIG_BT_BNEP)
- Networking → Bluetooth subsystem support → <*>HID protocol support (CONFIG_BT_HID)
- Networking → Bluetooth subsystem support → Bluetooth device drivers →
HCI USB driver (CONFIG_BT_HCIUSB)
- this is how my .config file was modified:
~/tonido/kernel-2.6.31$ diff .config.old .config 4c4 < # Sat May 12 21:21:58 2012 --- > # Sat May 12 22:24:11 2012 654c654,673 < # CONFIG_BT is not set --- > CONFIG_BT=y > CONFIG_BT_L2CAP=y > CONFIG_BT_SCO=y > CONFIG_BT_RFCOMM=y > CONFIG_BT_RFCOMM_TTY=y > CONFIG_BT_BNEP=y > # CONFIG_BT_BNEP_MC_FILTER is not set > # CONFIG_BT_BNEP_PROTO_FILTER is not set > CONFIG_BT_HIDP=y > > # > # Bluetooth device drivers > # > CONFIG_BT_HCIBTUSB=m > # CONFIG_BT_HCIBTSDIO is not set > # CONFIG_BT_HCIUART is not set > # CONFIG_BT_HCIBCM203X is not set > # CONFIG_BT_HCIBPA10X is not set > # CONFIG_BT_HCIBFUSB is not set > # CONFIG_BT_HCIVHCI is not set 1351a1371,1372 > CONFIG_HID_APPLE=y > CONFIG_HID_WACOM=y
You can continue with the instructions for building a TP2 kernel at step 15:
make uImage ...
Some attention points with the last activation step:
- remove two unnecessary symlinks before running scp:
~/tonido/kernel-2.6.31$ rm ../current_kernel/lib/modules/220.127.116.11-topkick1281p2-001-004-20101214/build ~/tonido/kernel-2.6.31$ rm ../current_kernel/lib/modules/18.104.22.168-topkick1281p2-001-004-20101214/source
- run scp (don't forget the -r for a directory):
~/tonido/kernel-2.6.31$ scp ../current_kernel/boot/uImage root@tp2-ip:/boot ~/tonido/kernel-2.6.31$ scp -r ../current_kernel/lib/modules root@tp2-ip:/lib/
- double-check if all transfers were OK before rebooting
If the TP2 booted successfully you can now enable and test bluetooth:
- apt-get install bluez
- test with hcitool:
root@TonidoPlug2:~# hcitool scan Scanning ... E4:D5:3D:EB:EA:E4 ubuntu-0 00:80:25:1F:9A:F4 SMA001d SN: ...
- forum thread on building a TP2 kernel: http://www.tonido.com/forum/viewtopic.php?f=37&t=4338&start=10
- generic instructions for setting up Bluetooth for the Linux kernel: http://www.thinkwiki.org/wiki/How_to_setup_Bluetooth#Configuring_the_kernel
- adding new modules for audio to the TP2 kernel: http://www.tonido.com/forum/viewtopic.php?f=37&t=4344